Real freedom demands new ways! Do you think so too? Then Cube have the perfect bike for you! The Nutrail Hybrid combines fatbike versatility and Bosch Power to create the ultimate overall package that literally opens new avenues.
Thanks to the 4.0 "tires, the powerful Bosch CX drive and the supple Manitou Mastodon Comp suspension fork, there are no limits anymore. Whether in the terrain - deep surfaces such as sand are his specialty - or in the middle of the urban jungle: This bike makes a casual figure everywhere. Cubes masterpiece has an aluminum frame that is specially tailored to the requirements of the Bosch system and fat tires. From the Shimano XT 11-speed gearshift to the powerful Magura MT5 hydraulic disc brakes to the telescopic seat post, Cube have put together a survival package that lets you confidently leave the familiar behind. On to new shores!
Whether 27.5 "or 29er: Larger wheels have clear advantages when rolling over obstacles and offer more traction and driving safety. However, they challenged the developers to give their bikes the familiar manoeuvrable and balanced ride of the previously used 26 "wheels. Several clever technical approaches have made this possible. Agile Ride Geometry: 1. For a CUBE 29er or 27.5 ", the bottom bracket height is the same as for a 26" bike 2. The derailleur position is designed so that, despite the low bottom bracket, the shift performance is 100 % patent pending), while giving more freedom to the front derailleur, keeping the rear end maximally short A further advantage of this construction: the seat tube does not have to be bent or offset. This results in the same seat tube angle for all driver sizes. 3. Cube use suspension forks with a special offset to always achieve a balanced fork overrun, even with the larger tire diameters. This results in a perfectly matched to the bike and usual steering behavior.
Noticeably more agility and, above all, rigidity - precise bike handling thanks to Boost 148mm technology. The hub flanges move 3mm outwards on either side, increasing stiffness by 14% on 27.5 "wheels and 21% on 29" wheels. The reason for this is the larger support surface of the spokes in comparison to the previously used 142mm wide hubs.
The wet paint process saves weight. On polished or brushed aluminum frames and on all HPC frames, logos and logos are protected by several layers of wet-applied paint.
The advantages of internally routed trains are obvious. As the lines disappear largely in the frame, they are optimally protected against external influences, pollute less and offer long-lasting top function. Of course, the appearance of the bike also gains through the tidy look.
In conventional thru axles, the radial and axial tension is carried out by repeated tightening various screw connections. In addition, missing conventional stub axle stops that allow a clean positioning of the rear hub. The axle diameter of the Syntace roof-mounted system is 12mm and the installation width is 142mm. The clamping of the stub axles takes place by means of a cone that enables backlash-free positive locking in the axial and radial directions. The axis only has to be tightened on one side. The positioning of the hub and locking the thru axle done by an insert in the right dropout, which is braced by a screw. The advantages of the Syntace Socket System: Simplified installation and removal of the rear wheel, a stable brake disc position (thus fewer loops) and better stiffness values of the rear triangle. To do this, X12 weighs less than conventional skylight systems.
This steering tube shape is stiffer and creates a safe ride even on difficult terrain. The direct power transmission creates the highest steering precision. The fork is also stiffer thanks to the larger fork stem. At the same time, you can save weight by eliminating bearing shells, because the lower bearings are fully integrated. With all CUBE carbon models, the upper bearing shells are located directly in the frame, so that a further few grams are saved and an even more direct power transmission is achieved. With this specially designed and patented CUBE stand mount, the bike stand is simply attached to the specially shaped frame mount from below and fixed with a screw from above. Due to the large support surface of the Radständerbasis directly on the frame high rigidity is achieved. This is especially important when loading luggage.